All kits are fully tested, include all parts, special tools, comprehensive installation instructions and limited phone support.

REPLACEMENT PARTS ONLY NOT FOR UPGRADING!
MODEL, S/N & original maximum RPM MUST BE SUPPLIED on your order
Note: if you give us a higher speed than the original - it WILL NOT WORK!

1009 0058 - WS-400x Keypad 

1009 0059 - WS-400x LCD

1009 0060 - WS-400B/E & -650x Pneumatic Vacuum Valve 

1009 0061 - WS-400x/-650s Power Conditioner (220 to 110 VAC)

1009 0062 - WS-400x/-650x Lid Sensor 

1009 0063 - WS-400x/-650s Standard Performance Motor Ass'y - Tabletop
must specify segments of encoder - 30 (2004 & before) or 60 (>2004 to present)
1009 0066 - WS-400x/-650s Standard Performance Motor Ass'y -  Indeck 
must specify segments of encoder - 30 (2004 & before) or 60 (>2004 to present)

1009 0064 - WS-400x/-650s Standard Performance Motor Controller
(must specify present maximum RPM [3K, 6K, 8K, 10K])

1009 0071 - WS-400x HPD High Performance Motor Ass'y - Tabletop

1009 0072 - WS-400x HPD High Performance Motor Ass'y - Indeck

1009 0073 - WS-400x/-650 HPD-2A High Performance Motor Ass'y (34) -  Tabletop (Cup & Cone vacuum seal - superseded by HPD-B)

1009 0074 - WS-400x/-650 HPD-2A High Performance Motor Ass'y (34)  - Indeck
(Cup & Cone vacuum seal - superseded by HPD-B)

1009 0075 - WS-400x/-650 HPD-2B High Performance Motor Ass'y (34)  - Tabletop

1009 0076 - WS-400x/-650 HPD-2B High Performance Motor Ass'y (34)  - Indeck

1009 XXXX - WS-400x/-650 HPD-2C High Performance Motor Ass'y (23) - Tabletop

1009 XXXX - WS-400x/-650 HPD-2C High Performance Motor Ass'y  (23) - Indeck

1009 0078 - WS-400x/-650 HPD-2 Brushless Motor Amplifier w/firmware

1009 0079 - WS-400x/-650x Power Supply 5 & 24 VDC

1009 0065 - WS-400x & -650s Seal Purge Pressure Sensor

1009 0067 - WS-400A 24 VDC Vacuum Control Valve

1009 0080 - WS-400x & -650x Vacuum Sensor (good soldering skill is req'd)

1009 0081 - Injector assembly (used on EDC system - standard fan spray)

1009 0082 - 1/4" Teflon control valve (as mounted on EDC manifold-Chemical)

1009 0083 - 3/8" Teflon control valve (as mounted on EDC manifold-Diffuser)

1009 0084 - 1/4" flare tool

1009 0085 - 3/8" flare tool

1009 0086 - 1" flare tool

1009 0087 - 100 feet (30.5 meters) of Teflon tubing

1009 xxxx - UD-1 Universal Dispenser with Viton Orings (for acids & Toluene)

1009 xxxx - UD-1 Universal Dispenser with EPDM Orings (for solvents)

1009 xxxx - UD-1b Universal Dispenser with Viton Orings (for acids & Toluene)

1009 xxxx - UD-1b Universal Dispenser with EPDM Orings (for solvents)

NOTE: We always recommend returning systems to the factory for firmware and other design updates, as well as for a complete analysis and repair. Because of the high likelihood of damaging these replacement parts by non-factory trained personnel there will be no returns except with entire system return/repair per our standard RMA procedure.